Stage Sound & Lighting

Click Photo to Enlarge

     
         
Equipment Rental
SSL Speakers
SSL FLC 2 X 12 With JBL 2446 Horn
SSL FLC 2 X 12 With JBL 2446 Horn
JBL 2445 Horn
JBL 2445 Horn
100 watts continuous program
at 500 Hz
150 watts continuous program at
1 kHz and higher
Coherent Wave™ phasing plug design
for increased high-frequency output
100 mm (4 in) pure titanium diaphragm
with radial-rib topology
and patented three-dimensional
diamond pattern suspension
100 mm (4 in) edgewound
aluminum voice coil
49 mm (2 in) throat exit diameter
100 watts continuous program
at 500 Hz
150 watts continuous program at
1 kHz and higher
Coherent Wave™ phasing plug design
for increased high-frequency output
100 mm (4 in) pure titanium diaphragm
with radial-rib topology
and patented three-dimensional
diamond pattern suspension
100 mm (4 in) edgewound
aluminum voice coil
49 mm (2 in) throat exit diameter
1201-8 Ohm BW Low Frequency Driver
1208-8 SPS BWX Low Frequency Driver
Impedance: 8 Ohms
Power capacity: 1400 W Peak,
700 W Program, 350 W Continuous
Sensitivity: 98.5 dB / 1 W 1 m
Usable freq. range: 60 Hz ~ 3.5 kHz
Cone: Kevlar® impregnated cellulose
Voice coil diameter: 4.0 inch / 100 mm
Voice coil material: Aluminum ribbon wire,
Polyimide-impregnated fiberglass former, Nomex® stiffener,
Solderless diffusion welded OFHC copper leads
Impedance: 8 Ohms
Power capacity: 2000 W Peak,
1000 W Program, 500 W Continuous
Sensitivity: 96.9 dB / 1 W 1 m
Usable freq. range: 50 Hz ~ 3.5 kHz
Cone: Kevlar® impregnated cellulose
Voice coil diameter: 4.0 inch / 100 mm
Voice coil material: Aluminum ribbon wire, Polyimide-impregnated fiberglass former, Nomex® stiffener, Solderless diffusion welded OFHC copper leads
   
SSL FLCM 2 X 15 With 22XT Horn Mid
SSL FLCL 2 X 15 With 22XT Horn Low
22XT Horn
22XT Horn
Patented titanium compression driver with 1 inch throat diameter
Ferrofluid cooled
Frequency response: 500 Hz - 20 kHz
Impedance: 8 Ohms
Mounts directly to all Peavey CH® horns with a 1 inch throat
Patented titanium compression driver with 1 inch throat diameter
Ferrofluid cooled
Frequency response: 500 Hz - 20 kHz
Impedance: 8 Ohms
Mounts directly to all Peavey CH® horns with a 1 inch throat
1502-8 DT BW Low Frequency Driver
15" Low Rider® Subwoofer
Impedance: 8 Ohms
Power capacity: 1400 W Peak,
700 W Program, 350 W Continuous
Sensitivity: 98.9 dB / 1 W 1 m
Usable freq. range: 40 Hz ~ 2 kHz
Cone: Kevlar® impregnated cellulose
Voice coil diameter: 4.0 inch / 100 mm
Voice coil material: Aluminum ribbon wire, Polyimide-impregnated fiberglass former, Nomex® stiffener,
Solderless diffusion welded OFHC copper leads

Impedance: 8 ohms
Power capacity: 3200 watts peak,
1600 watts program, 800 watts continuous
Sensitivity: 93.6 dB
Usable freq. range: 30 Hz - 1 kHz
Cone: Kevlar® impregnated cellulose
Voice coil diameter: 4.0 inch / 100 mm
Voice coil material: Polyimide coated copper ribbon wire, Polyimide-impregnated fiberglass former, Nomex® stiffener, Solderless diffusion welded OFHC copper leads
   
SSL FLS 2 X 18
18" Low Rider® Subwoofer

Field-replaceable basket
Kevlar®-impregnated cones for increased strength
Lower distortion due to greater dampening of excess cone vibrations
Polyimide-impregnated fiberglass former for higher sensitivity and frequency response
Die-cast aluminum frame
Higher power handling 4-inch diameter edge-wound voice coil
Impedance: 8 ohms
Power capacity: 3200 watts peak, 1600 watts program, 800 watts continuous
Sensitivity: 97.3 dB Usable freq. range: 25 Hz - 1 kHz
Cone: Kevlar® impregnated cellulose
Voice coil diameter: 4.0 inch / 100 mm Voice coil
material: Polyimide coated copperribbon wire Polyimide-impregnated fiberglass former Nomex® stiffener
Solderless diffusion welded OFHC copper leads
Monitors
1545 Wedge
Q-Wave Monitor

Two-way, full-range floor monitor
One 15 inch BWX Black Widow® woofer with Kevlar®/carbon fiber cone and field-replaceable basket, flat-wound voice coil and cast-frame basket
RX™ 22 compression driver with ferrofluid cooling and a 2 inch titanium diaphragm
Sound Guard™ HF driver protection circuit
Frequency response: 100 Hz - 14 kHz
-10 dB cutoff: 66 Hz Sensitivity: 99 dB (1W/1m)
Power handling: 1000 Watts program, 2000 Watts peak
8 Ohms Neutrik® full-range jack
30 or 45 degree baffle angle Baltic birch enclosure
New grille 45 degree baffle orientation: 15.63" H x 24.00" W x 17.75" D 30 degree baffle orientation: 15.25" H x 24.00" W x 17.75" D

Power handling:
Full range:

1,000 Watts continuous
2,000 Watts program
4,000 Watts peak
Low frequency section:
500 Watts continuous
1,000 Watts program
2,000 Watts peak
High frequency section:
100 Watts continuous
200 Watts program
400 Watts peak
Apex Architectural Speakers Enclosures
Apex AASE 2 X 15 Enclosures
High Horn
Compresson Driver PSD:2002
Throat Size 1", 25.4mm
Impedance 8 ohms or 16 ohms
Power Ratings: 80Wrms
(EIA426B specification, 1.6kHz @ 18dB) 550Hz
Resonance 1.5kHz - 20kHz
Usable Frequency Range 105dB
Sensitivity (1W @1m on axis on horn)
Magnet Weight 34oz.
Voice Coil Diameter 2", 51mm
Voice Coil Former DuPont Kapton
Diaphragm Material Titanium
 
High Mid and Monitors
General Specifications
Nominal Diameter 380 mm (15.0 inch)
Rated lmpedance 8 Ohm
Power Handling Capacity 600 W
Sensitivity 2.83 V, 1M 98 dB
Effective Piston Diameter 325 mm (12.8 inch)
Voice Coil Diameter 99.30 mm (4 inch)
Thiele & Small Parameters
Resonance Frequency FS 42.9 Hz
DC Resistance Re 6.9 Ohm
Mechanical Q Factor Qms 8.403
Electrical Q Factor Qes 0.322
Total Q Factor Qts 0.310
BL Factor BL 19.87 T x m
Effective Moving Mass Mms 68.33 g
Equivalent Cas air load Effettive piston area
Vas Sd 2 196.50 liters 0.0830 m
Voice -coil inductance@ 1KHz Le 1k 1.05 mH
Half -space efficiency Eff 4.67 %
Airgap Height Hag 8.0 mm
Voice coil Height Hvc 17.0 mm
Voice Coil Over -Hung Xmax 4.5 mm
HF Unit
Power Capacity (RMS) 100 W
Sensitivity 1W / 1M 109 dB
Ferquency Range 500 -18K Hz
Voice coil Diameter 72.2 mm 2.84 inch
Diaphragm Material Titanium
Dispersion Pattern 90 x 90
 
Low Mid

General Specifications C15-600EL
Nominal Diameter 385 mm (15.2 inch)
Rated lmpedance 8 Ohm
Power Handling Capacity 600 W
Sensitivity 2.83 V, 1M 97.1 dB
Effective Piston Diameter 325 mm (12.8 inch)
Voice Coil Diameter 99.30 mm (3.9 inch)
Basket Cast Aluminium
Magnet type,size ODxIDxH(mm) Ferrite
96.6 oz 200 x 110 x 25 mm
Voice coil Former Fiber Glass
Voice coil Material ALR
Cone Material Pulp Paper
Surround Treated Cloth
Dust Cap Pulp Paper
Unit Weight 10.37 Kg Gross Weight 11.90 Kg

 
Apex MTL 2 X 18 Enclosures

OMEGA PRO 18 high power bass
Nominal Basket Diameter 18", 457.2mm
Impedance 8 ohms
Power Rating 800Wrms
Resonance 28Hz
Usable Frequency Range 25Hz - 2kHz
Magnet Weight 109oz.
Gap Height 0.375", 9.52mm
Voice Coil Diameter 4.0", 101.6mm
GPS 3500 SPECIFICATIONS
Rated Power (2 x 2 ohms): 1750 watts @ 1 kHz both channels driven at <0.15% T.H.D.
Rated Power (2 x 4 ohms): 1200 watts @ 1 kHz both channels driven at <0.1% T.H.D.
Rated Power (2 x 8 ohms): 775 watts @ 1 kHz both channels driven at <0.1% T.H.D.
Rated Power (1 x 2 ohms): 1,850 watts @ 1 kHz at <0.1% T.H.D
Rated Power (1 x 4 ohms): 1,350 watts @ 1 kHz at <0.1% T.H.D
Rated Power (1 x 8 ohms): 850 watts @ 1 kHz at <0.05% T.H.D
Minimum Load Impedance: 2 ohms
Maximum RMS Voltage Swing: 89 volts
Frequency Response: 10 Hz - 100 kHz; +0, -.3d B at 1 watt
Power Bandwidth: 10 Hz - 40 kHz; +0, -3 dB at rated power
T.H.D. (2 x 2 ohms): <0.15% @ 1400W from 20 Hz to 20 kHz with both channels driven
T.H.D. (2 x 4 ohms): <0.1% @ 1050W from 20 Hz to 20 kHz with both channels driven
T.H.D. (2 x 8 ohms): <0.08% @ 750W from 20 Hz to 20 kHz with both channels driven
Input CMRR: > - 65 dB @ 1 kHz
Voltage Gain: x 40 (32 dB)
Crosstalk: > -75 dB @ 1 kHz at rated power @ 8 ohms
Hum and Noise: > -115 dB, “A” weighted referenced to rated power @ 8 ohms
Power Consumption: > 1400 watts
Slew Rate: > 40V/us
Damping Factor (8 ohms): > 325:1 @ 20 Hz - 1 kHz
SMPTE IMD: <0.1% 60Hz and 7 kHz, 950W @ 4 ohms
Input Sensitivity (x 40): 1.7 volts for 4 ohm rated power, 1.4 volts for 2 ohm rated power
Input Impedance: 20 k ohms, balanced
Current Draw @ 1/8 rated
power @ 2 ohms: 11.66 A@ 120 volts
Cooling: Two 80 mm DC fans, off until heatsinks reach 450C, then temperature dependent variable speed
Controls: Two front panel attenuators
Indicator LEDs: Two DDT/Clip, 2 Signal, 2 Power
Protection: Thermal, DC, turn-on bursts, subsonic, incorrect loads
Connectors: XLR input, 6.3mm phone type output patch, Speakon and Binding Post speaker output, IEC mains input
Construction: 16 ga. steel reinforced with 12 ga.rack ears
Dimensions:
133 mm x 483 mm x 432 mm, 400 mm behind rear mounting ears (5.23" x 19" x 17", 15.75" behind rack ears)
Weight: 51.3 lbs. (23.3 kg)
 
CS 1000 power amplifier
The world-famous CS 1000 power amplifier has been changed to the new, extended-performance
CS@ 1000X. This upgraded model provides impressive 2-ohm output power capability while still maintaining
the current 4- and & ohm ratings, and meets rigid industry standards for power bandwidth, slew rate, and
distortion specifications.
The new extended specs are:
525 W RMS into 4 ohms / 750 W RMS into 2 ohms (per channel)
1050 W RMS into 8 ohms / 1500 W RMS into 4 ohms (bridged)
DDTTM compression with LED indicators and defeat switch
Slew Rate: 40 V/microsecond, stereo mode, each channel
Power Bandwidth: 10 Hz to 50 kHz @ 4 ohms, rated power
Total Harmonic Distortion: less than 0.03%, rated power
Hum and Noise: 100 dB below rated power, unweighted
All the current features of the previous units have been retained, including Peavey’s patented DDTTM compression
system and the very flexible back-panel patching capabilities. The two-speed fan cooling system
has been improved to automatically provide additional cooling for the two-ohm load conditions.
 

Yamaha 3204
Specifications pdf
 

Yamaha 3204M
Specifications pdf
 

MX400 Yamaha
Specifications pdf

Maximum Output Level

+24 dB (Stereo L/R) @ 600ohm 0.5% THD at 1 kHz +20 dB (Group Out) @ 600 ohm 0.5% THD at 1kHz +20dB (Aux Send) @ 600ohm 0.5% THD at 1kHz +20 dB (Monitor) @ 600 ohm 0.5% THD at 1kHz
Total Harmonic Distortion
<0.1% @ +14dB 20Hz ~ 20kHz (St L/R, Group @ 600ohm Aux Send @ 600ohm)

Frequency Response
20 ~ 20kHz +1, -2dB (St L/R, Group @ 600ohm Aux Send @ 600 ohm)
Hum and Noise
(Average, Rs=150 ohm) Measured with a BPF, 20Hz ~ 20kHz) -128dB Equivalent Input Noise (Ch 1 ~ 24) -96dB Residual Output Noise (Stereo 1,2) -96dB Residual Output Noise (Group 1 ~4) -96dB Residual Output Noise (Aux Send 1 ~ 5) -87dB (Stereo 1,2, Group 1 ~4) Master fader at nominal level and all channel assign switch Off. -64dB (68dB S/N) (Stereo 1,2, Group 1 ~ 4) Master fader and 1CH fader at nominal -78dB (Aux Send 1 ~ 5) Aux Send master fader at nominal and all Ch. Aux level controls at minimum -64dB (68dB S/N) (Aux Send 1 ~ 5) Aux Send Master fader and 1 Ch Aux level control at nominal. -82dB (Stereo 2/Monitor) ST 2/ Monitor Master fader at nominal and all Ch. PFL and AFL switch Off. and St2/ Moni SW, select Moni -64dB (68dB S/N) (Stereo2/ Monitor) ST2/ Monitor Master fader at nominal and one channel PFL switch on, and ST2/ Moni SW., select Moni.

Maximum Voltage Gain
84dB Ch in to Stereo Out 1,2 84dB Ch in to Group Out 1~4 80dB Ch in to Aux Send 1,2 90dB Ch in to Aux Send 3 ~ 5 28dB Tape in to Stereo Out 1,2 30dB St Input to Stereo Out and Group Out 30dB St Input 1 ~ 4 to Aux Send 1 ~ 4 10 dB Group Sub In to Group out 10 dB St Sub In to Stereo Out 22dB 2 TRK In to Stereo 2/Monitor 70 dB Talk back to Stereo Out
Crosstalk at 1kHz
70 dB adjacent input channel 70 dB input to output
Input Channel Equalization +/-15dB maximum boost or cut in each 3 bands High 12kHz shelving Mid 250Hz ~ 5kHz peaking Low 80 Hz shelving *Turnover/Rolloff frequency of shelving; 3 dB below maximum Variable level.
Stereo Input equalization +/-15 dB maximum boost or cut in each 2 bands High 12kHz shelving Low 80Hz shelving *Turnover/ Rolloff frequency; 3dB below maximum Variable level.
Input Channel
HPF 80Hz 12dB/oct
Input Channel Gain Control
44dB variable from -60 to -16dB
Level meters
(0 point= +4dB output level) 6 x 11 segment LED meter -20, -15, -10, -7, -4, -2, 0, +2, +4, +6, Peak. #1, 2: Group 1,2 #3,4: Group 3,4 or ST2/ Monitor L,R #5,6: ST 1 L,R
Ch and St In Peak
Indicators Red LED on each channel turns on when post EQ signal reaches the level 3dB below clipping.
Ch and St in Signal Indicators
Green Led on each channel turns on when post EQ signal reaches the level -10dB.
Aux Send Peak Indicators
Red LED on each channel turns on when output signal reaches the level 3dB below clipping.
Aux Send Signal Indicators
Green LED on each channel turns on when output signal reaches the level -16 dB. Yellow LED on each channel turns on when output signal reaches the level 4dB.
Phantom power +48V DC
Power Requirement
UL/CSA model 120V AC 60 Hz, 80 W General model 230V AC 50 Hz, 80W
Dimensions
Height 180.2 mm (7-1/8") Depth 596 mm (23-1/2") Width 1042 mm (41")
Net Weight 28kg (61.7 lbs)

 


Peavey "SRM-2410 HC" 24 x 10 Monitor Console

Specifications pdf

Overview:
The SRM™ 2410 utilizes the latest in low-noise circuitry and surface mount technology. In addition, Peavey´s exclusive Feedback Locating System (FLS® ) can be found at each channel and at the two tunable notch filters. The result is a quiet, flexible monitor mixer packed with features.
24 true Transformer splits (XLR in/XLR thru)
48V Phantom Power switchable in banks of 8
TRS Insert on every input channel
-20 dB Pad on every input channel
Phase/Polarity Switch on 18 inputs
4-Band EQ with 2 mid Sweeps
8 Mono (1-8) Monitor sends and 1stereo pair (9/10)
Pre/Post switching for 1-6 and 7-8
Dedicated L/R bus
Precision 60 MM fader
Mute & PFL each channel
FLS® LED on each input to indicate loudest input channel
8 Mono and 1 stereo Sub master w/100 MM fader, AFL and Mutes
Adjustable HPF (Low Cut) on each Mono Sub
Two tunable Notch filters with FLS® tuning LEDs on each
1/4" Bal Send & Return Insert points, 1/4" bus inputs
Clearcom® compatible intercom
Built-in Universal Power Supply
Built into a roadworthy flight case

Specifications:
Frequency Response -20 Hz to 20 kHz +0/-1 dB
Input Sensitivity dBu --83
EIN dBu --126
THD + N -<0.05%
Agency Approvals -UL, CUL, CE
Operating Voltage -120/240 VAC
Dimensions -44" W x 9.25" H x 26.25" D
Weight -49.7 lbs.

 
Roland JC120
When the original JC-120 Jazz Chorus amp was introduced in 1975, its most obvious cosmetic distinction was its silver-cone speakers. And now these classic silver-cone speakers are back, giving the JC-120 the legendary clean amp sound found on countless records over the years. With the JC-120's lush chorus effects, dual-amp design and high-quality reverb, the "sound" is undeniable! 120 watts (60+60 stereo) and two 12" speakers.
DJ Sound

Click Photo to Enlarge
CD Mix 1

Numark CD Mix-1 Dual CD Player (Mixer only)
A dual CD player and DJ mixer all in one unit!
The CD Mix-1 gives you a pair of players and everything you need to keep grooves endlessly rolling. The players feature front-load transports with 30-second auto door close, track programming, 16% pitch/jog wheel, 12% pitch control, BPM counter, large backlit display, and true continuous play. The mixer offers one mic and 2 phone/line inputs for additional external devices, balanced output, master EQ, and stereo/mono control. It has built-in handles and when the party is in the great outdoors, you'll appreciate the 12V DC input.
DCX2496 Ultra-Drive Pro Crossover
Specifications pdf
Behringer DCX2496 Ultra-Drive Pro Crossover Features:

Signals can be split in various ways to assure precise sound by using the optimal frequency range of each loudspeaker
3 analog inputs (one suitable as a digital stereo AES/EBU input) and 6 analog outputs
Superb high-end AKM 24-bit/96kHz A/D/A converters
Dynamic range of 113dB
Easy connection of external digital signals with sampling rates from 32-96kHz is a breeze
Precise dynamic EQs for level-dependent equalization
Extremely musical parametric EQs selectable for all inputs and outputs
ÒZero"-attack limiters on all output channels guarantee optimal signal and loudspeaker protection
4 different mono and stereo output operating modes, all with individual crossover filter types (Butterworth, Bessel, and Linkwitz-Riley) with selectable roll-off characteristics from 6-48dB/octave
The delays for all inputs and outputs are adjustable
Future-proof Ultra-Drive Pro software enables single or multi remote control via PC